The gas-dynamic calcualation of the axial turbine stage

 

MINISTRY OF EDUCATION AND SCIENCE OF UKRAINEAviation University












The gas-dynamic calculation of THE axial turbine stage

Methodical guide for performing the course paper for students specialty 8.100106 Manufacturing, maintenance and repair of aircraft and engines



by I.I. Gvozdetsky , V.V. Kharyton, S.I.Tkachenko










KYIV 2007

Contents


Introductiongeneral law of circulation change across blade heightof the turbine stage geometrical dimensionsstage calculation on the middle radiusparameters determination on different turbine stage radiuses1 The example of gas-dynamic calculation of the axial turbine stage


Introduction

turbine serves to provide the power to drive the compressor and accessories. in a case of turboprop or turboshaft engine the turbine, in addition, provides the power to rotate propeller or rotor. It does this by extracting energy from the hot gases released from the combustion system and expanding them to a lower pressure and temperature. These processes take place when hot gases flow along specially shaped passages created by two rows of airfoils: stator vanes and rotor blades. These two rows of airfoils form a turbine stage. To produce the driving torque , the turbine unit may consist of one or several stages. The useful torque, created by turbine is transmitted to compressor by turbine shaft. Three stage turbine unite assembly is shown in fig.1.



this turbine unit can be divided into two main parts (fig.2): all rotating components (three bladed disks joined with shaft) are named turbine rotor, and all unmovable components (three turbine nozzle diaphragms and turbine casing) create the turbine stator.

The main objectives of turbine stage gas-dynamic calculation are determination of stage geometrical dimensions, gas cinematic parameters and speed plans construction. In course paper cinematic parameters are determined in three sections: sleeve, middle and peripheral.




Stage scheme, sections designation and diametrical dimensions are shown in figure 3.


. 3. Main geometrical dimensions of the turbine stage

initial data for turbine stage calculation are taken from gas-dynamic calculation of the designed engine. They are:

·full gas pressure and stagnated gas temperature at the entry to the turbine stage;

·mass gas flow rate ;

·turbine stage work ;

·circumferential velocity on the middle radius of the working wheel ;

·jet velocity of gas at the exit from the nozzle diaphragm ;

·reduced velocity at the nozzle diaphragm exit ;

·angle of the stream output from the nozzle diaphragm ;

·pressure recovery coefficient in the nozzle diaphragm ;

·external, middle and sleeve diameters at the entry to the working wheel ; ; .

All of these parameters are chosen for the first turbine stage of the designed engine.

The general law of circulation change across blade height

gas work, the reactivity rate, the gas velocity, Mach numbers, efficiency, blade incidence angles and other parameters depend on law of circulation change across stage working wheel radius. Different laws of circulation change across radius are expressed by general equation


, (1); m - index rate.


If m=1 law of circulation constancy is implemented. This law of profiling is used for comparatively short blades (), because in this case reactivity rate across blade height is changed very essentially. And using long blades the reactivity rate can be negative near sleeve.longer blades profiling with index rate m<1 is applied. Particularly, for law of profiling with constant angle of the stream output from nozzle diaphragm is realized.obtain small m angle is increased. It causes increase of the axial gas velocity, which can reach local sonic speed at exit from working wheel. It will mean choking of the turbine stage. As a result, it is no point in increasing of angle more then on 20-25° at first stages. At these values negative reactivity rate can occur near blade root, especially at high values of loading coefficient.a result of this, profiling on the base of equation (1) is common, because it gives possibility to avoid negative values of the reactivity rate near the blade root by matching of rate index m at the all values.

Determination of the turbine stage geometrical dimensions

dimensions at the entry to the working wheel are determined in the gas-dynamic calculation of the designed engine. At first area at the exit from the nozzle diaphragm is calculated


,

and are stagnated temperature and full pressure of the flow at the exit from the nozzle diaphragm; ; ; mg - constant magnitude, which can be computed by the formula


kg=1,33 and Rg=288 J/(kg×K) we will have mg=0,0396 (kg×K)/J.density can be determined from tables of gas-dynamic functions using value of the reduced velocity or by the formula


.

he given working wheel middle diameter other geometrical dimensions are computed by the following formulas:


; ; .

At he given relative sleeve diameter geometrical dimensions in the considered section are computed by the formulas:


sleeve diameter for first stages is within the limits of , and for last stages .first turbine stages the nozzle diaphragm is profiled to provide turbine blending with combustion chamber. In this case meridional profile of the nozzle diaphragm can be of arbitrary shape with the obligatory observance of sections areas.calculate section area at the exit from the stage (behind working wheel) it is necessary to compute gas parameters and behind calculated stage.gas temperature is determined from the energy equation:


gas pressure behind stage is calculated by the formula


- stage efficiency.component of the jet velocity at the exit from the working wheel is assumed on 20-80 m/s more then gas velocity at the entry to the working wheel, i.e.


; m/s,.

area at the exit from the working wheel is determined from following expression:


,

is computed by the value of


.

for chosen profiling law determine main dimensions at the exit from turbine stage in a similar manner as have been done turbine stage entrance.the base of computed diameters values draw turbine stage scheme.


Turbine stage calculation on the middle radius


At given circumferential velocity value on the middle radius of the inlet edge calculate circumferential velocity behind working wheel from the relation


Performing approximate calculations it is possible to suppose.loading coefficient on the middle radius is determined by the formula


the first turbine stage .jet velocity at the exit from the nozzle diaphragm is determined from the equation


reduced velocity - by the formula


of must not exceed 1,25. If it is possible to decrease it by increasing the circumferential velocity , decreasing of the angle of the stream output from nozzle diaphragm , increasing of the stage work, applying of airtwist at the exit from the working wheel in the opposite direction of rotation. If first three methods can not be used, can be obtained from the Eulers equation, have assigned:


,

where .

of must not exceed, otherwise it is necessary to decrease to meet this requirement.long as all of calculations are carried out for middle radius in what follows we will withdraw subscript md. Following formulas flow parameters calculation are legible for every blade section.components of the jet velocity at the entry to the working wheel and behind turbine stage, and parameters , and are calculated by the formulas:


; ; ;

.

component of the jet velocity and parameter at the entry to the working wheel are calculated by the formulas:


; .

component of the relative velocity and the relative velocity at the entry to the working wheel are calculated by the formulas:


; .

of the stream inlet into the working wheel in the relative direction is computed by formula

.

component of the relative velocity behind turbine stage is determined on the base of the following expression


axial turbine stage

Axial component of the jet velocity at the exit from the working wheel is assigned such that is on (20-80) m/s more then.velocity and reduced velocity at the exit from the working wheel are calculated by the formulas:


; .

output angle at the exit from the working wheel is calculated by the formula


.

must be close to 90°, but for first stages it can be n the range of (75-85)°.output angle at the exit from the working wheel in the relative direction can be found by the formula


.velocity at the exit from the working wheel and its circumferential component are determined by the formulas:


; .

temperature and critical gas velocity in the relative direction are computed from the equations:


velocities at the entry to the working wheel and behind turbine stage are calculated by the formulas:


; .

reactivity rate is determined from the equation


,

is airtwist in the working wheel.of on the middle radius must be within limits of 0,2-0,35.verify calculations accuracy it is necessary to compute turbine stage work by the formula

.

obtained value differs more than on 3% from accepted at the beginning it is necessary to look for mistake in previous calculations.


Cinematic parameters determination on different turbine stage radiuses

plan calculation and construction (see pic. X.x) is done for chosen law of blade profiling across radius.


. X.x

approximate turbine stage calculations we can accept design sections diameters as average between diameters of inlet and output edge, i.e.


flow parameters calculation first of all law of blade profiling across radius are chosen. For that reactivity rate are determined at rate index value m=1,0 () from the equation

.

, the law of circulation constancy is accepted, which provide high stage efficiency. In this case angle of nozzle diaphragm blade incidence is changed across blade height., blades can be profiled by the law of , which allows to obtain same profiles across the blade height and simplifies blade manufacturing technology. Disadvantage of these blades is non-constant axial component of the jet velocity at the exit from the nozzle diaphragm. If value is obtained at index value m=1,0, then assigning , index value m can be found by the formulas:


, if ;

, if .

and on different radiuses in common case are calculated from the equations:


;

.

the law of profiling is accepted, then:

; .

the law of profiling is accepted, velocities and

are calculated from the equations (x.x) and (x.x) with index value .components of the jet velocity are determined by the formulas:


;

.

the law of profiling is accepted, then:


;.

the law of profiling is accepted, velocities and

are calculated from the equations (x.x) and (x.x) with index value .


Table 1cinematic parameters on different radiuses

Parameter and formulaSectionNotesleevemiddleperipheral, m, m/s, m/s,m/s, m/s, deg, m/s, m/s, deg, m/s, m/s, m/s, deg, deg, m/s, m/s, K,J/kg, %

Appendix 1


THE EXAMPLE OF gas-dynamic CALCULATION OF THE axial turbine stage


The initial data for the axial turbine stage gas-dynamic calculation are gas parameters and geometrical dimensions at the entry to the turbine obtained during gas-dynamic calculation of the designed engine.main goals of the turbine stage gas-dynamic calculation are geometrical dimensions determinationof the turbine stage, speed plans construction in three sections across the blade height.the engine gas-dynamic calculation following parameters are known:

·gas pressure at the entry to the high-pressure turbine ;

·gas temperature at the entry to the high-pressure turbine ;

·mass gas flow rate ;

·HPT stage work ;

·circumferential velocity on the middle radius ;

·angle of the stream output from nozzle diaphragm ;

·external, middle and sleeve diameters at the entry to the working wheel , , ;

·jet velocity of gas at the exit from the nozzle diaphragm ;

·reduced velocity at the nozzle diaphragm exit ;

·pressure recovery coefficient in the nozzle diaphragm .

Section area at the entry to the HPT first stage working wheel was determined in the engine gas-dynamic calculation:

.

relative density and then;

.dimensions before the working wheel will be found on the basis of the next formulas:

·blade height


;


·external diameter


;


·sleeve diameter


;


·relative sleeve diameter


;

determine geometrical dimensions at the exit from the working wheel, first of all, it is necessary to compute flow parameters in this section.temperature at the exit from the turbine stage is calculated from the equation


; .

pressure at the exit from the turbine stage is calculated by the formula


; ,

.component of the jet velocity is assigned at the exit from the working wheel:

;


;;.

velocity is calculated by the formula


; ,.

area at the exit from the working wheel is calculated from the equation

;

.

, we assume.dimensions at the working wheel exit:


;

;

;

stage flow duct are drown in scale x:x (see pic x.x)


. X.x Turbine stage flow duct

is necessary to determine stage loading coefficient for turbine stage calculation on the middle radius:

;

velocity and reduced velocity at the exit from the nozzle diaphragm is computed supposing axial flow output, i.e. :


; ;

; .

component of the jet velocity and parameter at the entry to the working wheel are calculated by the formulas:


; ;

; .

components of the jet velocity at the entry to the working wheel and behind turbine stage, and parameters , and are calculated by the formulas:


; ;

; ;

; ;

; ;

; .

gas velocity and its circumferential component can be found from the expressions:


;;

; .

of the stream inlet into the working wheel in the relative direction is computed by formula


; .

velocity and reduced velocity at the exit from the working wheel are calculated by the formulas:


; ;

; .

output angle at the exit from the working wheel in the relative direction can be found by the formula


; .

velocity at the exit from the working wheel and its circumferential component are determined by the formulas:


; ;

; .

temperature and critical gas velocity in the relative direction are computed from the equations:


;


;


; .

is calculated by the formula


; .

velocities at the entry to the working wheel and behind turbine stage are calculated by the formulas:


;

;

Cinematic reactivity rate is determined from the equation


; .

velocities at the entry to the working wheel and behind it are accepted the same (). Turbine stage work is verified by the equation


;

;

; .

, all calculations are correct.calculate flow parameters on different radiuses, first of all, it is necessary to choose law of profiling across blade height. To do it, calculate reactivity rate an rate index value m=1:


;

.

,we choose law of circulation constancy across the radius .parameters calculations on different radiuses are summarized in the table x.x.

Table X.x

Parameter and formulaSectionsleevemiddleperipheral, m0,6860,7180,75, m/s382400417,81,681,531,4, m/s222,9222,9222,9,m/s641,1612,5586,4, m/s678,7651,8627,3

,966

,927

0,892, deg

.3

.3

22.3, m/s259,1212,5168,6, m/s341,8308279,5, deg

,7

,4

52,9, m/s263,6263,6263,6, m/s000, m/s263,6263,6263,6, deg



90

,4

,4

0,4, deg

,6

,4

32,2, m/s

,2


494,7, m/s382,1400418,6, K



1364

,51

,46

0,42

,696

,716

0,738

,16

,234

0,3,J/kg



245314, %

,04

,013

0,13the basis of foregoing calculation we plot speed plans for three sections on blade height (see pic. X).


)

)


). X.x. Axial turbine stage speed plans:- sleeve section; b - middle section; c- peripheral section.


MINISTRY OF EDUCATION AND SCIENCE OF UKRAINEAviation University The gas-dynamic calculation of THE axial turbine

Больше работ по теме:

КОНТАКТНЫЙ EMAIL: [email protected]

Скачать реферат © 2018 | Пользовательское соглашение

Скачать      Реферат

ПРОФЕССИОНАЛЬНАЯ ПОМОЩЬ СТУДЕНТАМ